-
Teflon mesh conveyor belt has the characteristics of easy permeability of mesh, so it is widely used in textile printing and dyeing, printing drying guide belt, screen printing, UV drying, UV series, light curing machine, offset printing machine, loose dryer, non-woven drying machine, high frequency dryer, food drying machine guide belt, temperature control drying room Equipment for fast drying of flux ink and drying of general moisture containing articles.
Published on: July 25, 2020 Number of hits: 67
-
How to share the scar of heat-resistant conveyor belt? The appearance defects of the heat-resistant conveyor belt and their causes. The surface of the covered rubber is slightly concave, which is the most common appearance defect of the heat-resistant conveyor belt. The main causes are: the plastic property of the rubber is too small, which results in poor fluidity. If the combination of the covering rubber of ethylene propylene rubber is unreasonable, especially if the softener is used improperly, the plastic property of the rubber is small, and the fluidity is poor
Published on: February 22, 2020 Number of hits: 45
-
1、 Startup and shutdown: the conveyor shall be started under no-load condition generally. When several belt conveyors are installed in sequence, the lockable starting device shall be used to start and stop in a certain order through the central control room. In addition to Teflon conveyor belt, in order to prevent accidents, each conveyor should also be equipped with a local start or stop button, which can stop any one separately
Published on: February 21, 2020 Number of hits: 64
-
The use of conveyor belts has covered a wide range of areas, and conveyor belts can be seen wherever there is a conveyor. The conveyor belt has many advantages such as safe operation, simple use, saving manpower and material resources, which can reduce the project cost and create greater benefits. In fact, the maintenance of the conveyor belt is relatively simple, and the maintenance cost is not high, which is favored by the society. Because of its extensive transportation
Published on: February 18, 2020 Clicks: 56
-
Appearance defects and formation reasons of high-temperature resistant conveyor belt: the covered rubber surface is slightly concave, which is the most common appearance defect of high-temperature resistant conveyor belt. The main causes are: the plastic property of rubber material is too small, which leads to poor fluidity. If the matching combination of the covering rubber material of ethylene propylene rubber is unreasonable, especially the softener
Published on: February 17, 2020 Number of hits: 47
-
The production process of Teflon mesh belt: select high-quality glass fiber, use special knitting process for processing, then soak it, soak it, and then carry out various processes of coating. Teflon mesh belt with
Published on: February 14, 2020 Clicks: 191
-
Teflon high-temperature cloth, also known as Teflon high-temperature cloth, is made from imported polytetrafluoroethylene (PTFE) emulsion and impregnated with high-performance glass fiber cloth. It is a new composite product with high performance and multi-purpose. In the future, Jiangsu will revitalize fluoroplastics to meet the performance requirements of future customers and markets for Teflon mesh belts
Published on: February 13, 2020 Clicks: 93
-
Introduction to the cause of deviation of Teflon conveyor belt: deviation of conveyor belt is one of the most common faults when the belt conveyor is running. There are many reasons for deviation. The main reasons are low installation accuracy and poor daily maintenance. During installation, the head and tail rollers and the intermediate idler rollers shall be on the same centerline as far as possible and parallel to each other to ensure that the conveyor belt is not biased or slightly biased. In addition, the belt is connected
Published on: November 6, 2021-10 Number of hits: 244
-
Teflon non stick coating: During baking, perfluoroalkylated non stick coating melts and flows like FEP to form a pore free film. PFA has a higher continuous service temperature of 260 ℃, stronger rigidity and toughness, and is especially suitable for anti sticking and chemical resistance under high temperature conditions. Teflon PTFE: P
Published on: September 24, 2019 Clicks: 166
-
Suzhou Tuoyang New Material Technology Co., Ltd., located in Guli Town, Changshu, Suzhou, is a manufacturer of a series of high temperature resistant products such as polytetrafluoroethylene and perfluoroethylene. The company has production equipment and R&D personnel with strong technical strength. The R&D team is centered on senior engineers engaged in film and film industry and personnel with rich manufacturing experience. The products are widely used in instruments
Published on: August 10, 2019 Number of hits: 180
-
Suzhou Tuoyang New Material Technology Co., Ltd. specializes in producing Teflon conveyor belts, which are divided into Teflon mesh belts and Teflon high-temperature cloth. Teflon conveyor belt Teflon high temperature cloth is mainly used for: 1. Anti adhesive lining, gasket, cloth and conveyor belt according to its temperature resistance, corrosion resistance, anti adhesion, etc; According to the thickness, the conveyor belt is used for various drying machines,
Published on: September 4, 2018 Clicks: 219
-
Is Teflon mesh belt UV mesh belt? UV mesh belt is a mesh conveyor belt used by UV curing machine. Teflon mesh belt is made of glass fiber or Kevlar woven mesh fabric as the base material and coated with high-quality Teflon resin. The common point of both types is mesh, both are used for conveying. Teflon conveyor belt manufacturers will talk about the differences below. UV net
Published on: March 31, 2018 Number of hits: 241
-
Teflon high temperature drying mesh belt is often polluted by one kind of goods in use, and paint pollution is a common situation. So, what method can be used to clean the Teflon mesh belt after it is stained with paint? Listen to me. The main components of paint are oil, resin, pigment, thinner and auxiliary materials. Considering their components, we can easily get
Published on: March 31, 2018 Clicks: 109
